Resolution 231-2015 1
2
3 . •
t
5 �.
6v �
•
8
9 MONROE COUNTY,FLORIDA
10 MONROE COUNTY BOARD OF COUNTY COMMISSIONERS
11 RESOLUTION NO. 231 -2015
12
13 A RESOLUTION OF THE MONROE COUNTY BOARD OF
14 COUNTY COMMISSIONERS ADOPTING FEMA TECHNICAL
15 BULLETIN 8 "CORROSION PROTECTION FOR METAL
16 CONNECTORS IN COASTAL AREAS" DATED AUGUST 1996 AS
17 REQUIRED PURSUANT TO MONROE COUNTY CODE
18 SECTION 122-2(C)
19
20
21 WHEREAS, Monroe County is currently a participating community in the National
22 Flood Insurance Program (NFIP) and is working on internal County policies to improve upon its
23 interpretation of NFIP regulations; and
24
25 WHEREAS, Monroe County desires to become eligible to enter FEMA's Community
26 Rating System(CRS); and
27
28 WHEREAS, Monroe County Code Section 122-2(c), in part, requires that in interpreting
29 other provisions of this chapter, the building official shall be guided by the current edition of
30 FEMA's 44 CFR, and FEMA's interpretive letters, policy statements and technical bulletins as
31 adopted by resolution from time to time by the board of county commissioners;
32
33 NOW, THEREFORE, BE IT RESOLVED BY THE BOARD OF COUNTY
34 COMMISSIONERS OF MONROE COUNTY,FLORIDA:
35
36 Section 1. Pursuant to Monroe County Code Section 122-2(c), the Board hereby adopts
37 FEMA Technical Bulletin 8 "Corrosion Protection for Metal Connectors in Coastal Areas" dated
38 August 1996, a copy of which is attached hereto.
39
40 Section 2. The Clerk of the Board is hereby directed to forward one (1) certified copy of
41 this Resolution to the Building Department.
42
43
44
45
1 PASSED AND ADOPTED by the Board of County Commissioners of Monroe County,
2 Florida, at a regular meeting held on the 16th of September, 2015.
3
4
5 Mayor Danny L. Kolhage Y e s
6 Mayor pro tern Heather Carruthers Y e s
7 Commissioner Sylvia Murphy Yes
8 Commissioner George Neugent Y e s
9 Commissioner David Rice Y e s
10
11
12
13 BOARD OF COUNTY COMMISSIONERS
14 OF MONROE COUNTY, FLORIDA
1 t
16 BY:
17 Mayo L. Kolhage
18 06%
f'.:4'-ailN1•
- Y HEAVILIN, CLERK,
_�
�- , mo ii!
.0
clUNTYATTORNFV
(<OVED AS FORS.°
STEVEN T. Wlll
'SISTANT r,Q i
Jate rain IS—
r.:
''. Tethmca1
440firlir
`... '.1. B ulletin
8-96
Corrosion Protection for Metal Connectors in Coastal Areas
for Structures Located in Special Flood Hazard Areas
in accordance with the
National Flood Insurance Program
411111ft
w. . _
-
•
• .
0 k\ii
s t
I I I 1 I
virew_-Jam` ;.
• ,
(____ •........
I • , '0/°>%% .
4I
di FEDERAL EMERGENCY MANAGEMENTAGENCY FIA-TB-8
r.�y
MITIGATION Directorate (8196)
'
Key Word/Subject Index:
This index allows the user to locate key words and subjects in this Technical Bulletin. .�
The Technical Bulletin User's Guide (printed separately) provides references to key
words and subjects throughout the Technical Bulletins. For definitions of selected terms,
refer to the Glossary at the end of this bulletin.
Key Word/Subject Page
Corrosion,classes of building exposure to 5
Corrosion,causes of 3
Corrosion,planning for 7
Corrosion, identifying high-risk buildings 5
Corrosion-resistant materials for sheetmetal connectors 6, 7, 9
Galvanizing 2
Salt spray from breaking waves 3
Any comments on the Technical Bulletins should be directed to:
FEMA/ Mitigation Directorate
Program Development Branch
500 C Street, SW.
Washington, DC 20472
Graphic wave design on cover based on the Japanese pnnt The Great Wave Off Kanagawa,by Katsushika Hokusi
(1760-1849),Asiatic Collection.Museum of Fine Arts,Boston.
TECHNICAL BULLETIN 8-96
�.. Corrosion Protection for Metal Connectors in Coastal Areas
Introduction
An important objective of the National Flood Insurance Program (NFIP) is to protect buildings
from the effects of hurricanes.The NFIP regulations include requirements concerning the
resistance of buildings to flood and wind forces (as described in the following section). For a
building in a Coastal High Hazard Area to comply with these requirements, many of its
components must be adequately anchored. In wood-frame buildings,the necessary anchoring is
usually achieved through the use of metal connectors such as joist hangers, truss plates, and
hurricane straps.The need for such connectors is especially great in coastal areas, where storm-
induced flooding and high winds pose significant threats. However, metal connectors are subject
to corrosion when exposed to moisture and salt,both of which are prevalent in coastal areas.
This bulletin describes the causes of accelerated corrosion of metal connectors in buildings
located near the ocean and some larger saltwater bays. The variation in the corrosive
environments within a typical building is also described. This bulletin outlines available
corrosion-resistant materials and methods of maintaining proper anchorage for the life of the
building. It recommends connector materials for buildings at various distances from the ocean
and for different exposure conditions within an individual building. Few local building codes and
no national building codes address accelerated corrosion near the coast.This bulletin describes
areas where corrosion is known to be a problem and recommends a variety of solutions.
NFIP Regulations
Section 60.3(a)(3)of the NFIP regulations states that the community shall:
"Review all permit applications to determine whether proposed building sites will be
reasonably safe from flooding. If a proposed building site is in a flood-prone area, all
new construction and substantial improvements shall(i)be designed(or modified)and
adequately anchored to prevent flotation, collapse. or lateral movement of the
structure..."
And Section 60.3(e)(4) states that the community shall:
"Provide that new construction and substantial improvements in...(the coastal high
hazard area)...are elevated on pilings and columns so that...(ii)the pile or column
foundation and structure attached thereto is anchored to resist flotation, collapse and
lateral movement due to the effects of wind and water loads acting simultaneously on all
building components. Water loading values shall be those associated with the base flood.
Wind loading values used shall be those required by applicable State or local building
standards. A registered professional engineer or architect shall develop or review the
structural design specifications and plans for the construction, and shall certify that the
design and methods of construction to be used are in accordance with accepted standards
of practice for meeting the provisions of paragraphs... (ii)of this section. "
1
Standard Metal Connectors 7TopChord
of Truss
Common Uses sheetmetal e o of
When buildings are damaged by natural hazards Wind Anchor 'O °°° Wood Truss
such as high wind, waves, flooding, and i '
earthquakes, the structural damage usually does
Chord of
not start with a wood board breaking.The weak t -=== Truss
link is normally the connection between i i shoo al
Truss Plate
individual wooden members, and it is here that ° To,•at
structural failure often begins. In many cases,
replacing conventional nailing with a sheetmetal 0
connector produces a connection over 10 times e
stronger. Hurricanes and earthquakes have °'�� will Stud
demonstrated repeatedly that for most buildings,
good connections often make the difference
between survival and severe damage. Figure I. Wind anchor and truss plate
Typical metal connectors that are potentially
Double subject to corrosion include hurricane straps
Double
` Floor Band and wind anchors used to connect roofs to
Joist
Hanger walls (see Figure 1); truss plates that connect
6 the separate members of premanufactured
#111G roof and floor systems(see Figure 1);joist
hangers used on floor joists, beams, and
Double rafters(see Figure 2); and various other metal `�
Jo"` straps used to connect wood components
Elixir throughout the building.These include straps
Joist HangerJoist that attach the roof to the walls and prevent
the aerodynamic lift of high winds from
removing the roof or displacement caused by
lateral forces during earthquakes.
Figure 2. Single and double joist hangers
Standard Materials:Galvanized Steel
Most connectors are fabricated from steel sheetmetal. In thin sheets,steel is sufficiently strong,
readily workable, and relatively inexpensive, characteristics that make it well-suited for
connectors. However, bare steel is subject to corrosion,or rusting,even in inland areas, and it
corrodes rapidly in salt air. Most sheetmetal connectors, therefore, are galvanized for corrosion
protection. Galvanizing is the process of coating steel with zinc. After careful cleaning, the steel
sheet is dipped into a vat of molten zinc.The high temperature melts the surface of the steel and
forms several steel/zinc alloys to tightly bond the zinc coating to the steel base metal. The
coating of zinc still corrodes, but generally over 50 times more slowly than steel in the same salt
air environment.
Galvanizing is particularly effective for steel because, unlike most other coatings,the zinc
sacrificially protects any bare steel edges or scratches.The zinc surface near a scratch will
corrode slightly faster than the zinc surrounding it and will fill small scratches with zinc --/
2
corrosion products,preventing the steel from rusting until the nearby zinc is consumed. Zinc also
differs from other coatings (or paints) and most metals by corroding at a relatively steady rate in
most atmospheric exposures.Therefore,doubling the thickness of the zinc coating approximately
doubles the protection period.
Most connectors are fabricated after the steel sheetmetal has been galvanized.The American
Society for Testing and Materials(ASTM)has established national standards for galvanizing that
are accepted by the Standard(Southern Building Code Congress International), National
(Building Officials& Code Administrators International), Uniform (International Conference of
Building Officials),and most local building codes. Most connector manufacturers specify ASTM
A-525 G 60 for the galvanized steel sheetmetal from which connectors are fabricated. ASTM A-
' 525 is a general standard that establishes a variety of galvanizing thicknesses identified by
different G numbers.The G 60 designation used for most connectors indicates a zinc coating
thickness of 0.5 mil (1 mil =0.001 inch)on each side of the steel. The numerical G designation
increases or decreases proportionally with the coating thickness. For example, the coating of zinc
on a G 90 connector is 1.5 times thicker than that on a G 60 connector.
Causes of Corrosion Near the Ocean
The conditions that accelerate corrosion near the coast have been studied in a few corrosion field
stations and research laboratories around the world. Several of these conditions occur along most
shorelines. Understanding the causes of accelerated corrosion can help identify some of the worst
corrosion exposures that affect coastal buildings.
Salt Spray from Breaking Waves and Onshore Winds
Salt spray from breaking waves and onshore winds significantly accelerates the corrosion of
metal connectors. The ocean salts,which are primarily sodium chloride but include other
compounds, accumulate on the metal surfaces and accelerate the electrochemical reactions that
cause rusting and other forms of corrosion.The combination of salt accumulation on the surface
and the high humidity common to many coastal areas significantly accelerates the corrosion rate
of steel and other metals commonly used for connectors or other building materials.The longer a
surface remains damp during normal daily fluctuations in humidity,the higher the corrosion rate.
Onshore winds carry both salt and moisture inland.Therefore,corrosion rates along shorelines
with predominately onshore winds will be higher than those along shorelines with predominately
offshore winds.
Distance from the Ocean
Corrosion rates vary considerably from community to community. But the amount of salt spray
in the air is greatest near the breaking waves and can decline rapidly in the first 300 to 3000 feet
(roughly 100 to 1000 meters) landward of the shoreline. Farther landward,corrosion is akin to
that which occurs in milder, inland conditions.The width of the high-corrosion zone must be
determined in each community, but oceanfront buildings will always be more severely affected
than buildings farther inland.
One series of tests in North Carolina in the 1940s found that samples of iron corroded 10 times
faster at 80 feet ( 25 meters) landward of the shoreline than samples of the same type at 800 feet
�.. (250 meters) landward of the shoreline (LaQue, 1975. see#6 in the section titled "Further
3
Information"). Similar results have been noted around the world. Where waves break, salt is
tossed into the air and the wind tends to distribute the salt spray to inland areas.
Corrosion Rate Elevation
Variation with Elevation Other tests conducted in North Carolina found
35 that corrosion reached a peak at about 12 feet
80 Ft.
30- from Ft from (3.6 meters) above the ground(see Figure 3),
25 - Ocean Ocean approximately equal to the lowest floor
; Peak elevation of an elevated building with lower
20- Corrosion level parking. Several rows of buildings
15 - Rate farther inland,the overall corrosion rate is
lower,but it is highest at an elevation above
10 " the roofs of small buildings. Figure 3 also
5 _ indicates that the worst corrosion nearest the
ocean was more than double the worst farther
0 ' ' inland.
0 10 20 30
Corrosion Rate(mils/yr)
Shelter and Orientation
Figure 3. The variation in the corrosion rate of steel Bold exposures such as building exteriors are
with elevation for Kure Beach, NC coated with large amounts of salt spray and
can be expected to suffer high corrosion rates. But partially sheltered exposures, such as
underneath open, piling-supported buildings or underneath decks and walkways,can sustain
even worse corrosion than bold exposures.The results of other exposure tests from near the •ft.i
ocean in Kure Beach are shown in Figure 4(LaQue, 1975). Steel samples were weighed,then
exposed under a wooden roof. After 2 years. rust and other corrosion products were stripped
from the samples, and the samples were weighed again to measure the weight loss.
The study reported that salt spray accumulations on bold exposures are rinsed periodically by
rainfall (Positions 4 and 5), reducing the surface salt concentrations. Sheltered exposures receive
little salt spray (Position I). Partially sheltered exposures(Positions 2 and 3) receive almost as
much incoming spray as bold exposures. However, the surface concentrations remain high,
Shelter
400
I
Test
2 Roof
300_ Plate Position#i — I
3 2
.c 200.
3 4 3
100 5
a 4
� r r
North East South West - 5
(ocean)
Figure 4. The effect of shelter and orientation under the test roof shown on the right
4
because of the shelter from cleansing rain. An additional factor is the duration of surface
wetness. Accelerated corrosion occurs primarily when a certain level of surface wetness is
exceeded, initiating electrochemical reactions among the metal,salts, and air. Bold exposures are
more rapidly dried because they are exposed to sunlight. Drying slows the corrosion rate.
Partially sheltered exposures stay damp longer and therefore corrode faster. The effect of
building orientation on corrosion is also shown in Figure 4. The metals on the side of a building
facing the ocean will corrode much faster than those facing away from the ocean.
Weather and Time
Weather affects the rate of corrosion in all exposures, both coastal and inland. Most chemical
reactions, including corrosion rates, are affected by temperature, humidity, wind speed, and other
factors. Like any weather-driven condition, the corrosion rate can vary considerably from year to
year. Average conditions for factors like rainfall seldom occur.The measured rainfall is often
either much higher or much lower than the average. Average years seldom occur. Likewise, the
annual corrosion rate in any individual year will be significantly higher or lower than the long-
term average. Therefore, annual measurements of corrosion can be very misleading unless
compared to long-term averages for nearby locations.
Identifying Corrosion-Prone Buildings
In a few communities, corrosion test facilities can predict the distance from the shoreline at
which corrosion will be most severe. Unfortunately, in most communities,corrosion data will not
be available. Estimates of the width of the zone where corrosion-resistant materials and methods
arc necessary should be based on local experience. Metal connectors should be observed in older
buildings at various distances from the shoreline. If oceanfront buildings are experiencing severe
corrosion problems in less than 10 years. then the second or third row buildings will experience
severe corrosion over a typical useful lifetime of 50 to 70 years.
Classes of Exposure for Connectors in a Building
Corrosion exposures for metal connectors in most buildings can he grouped into five classes,
four of which are shown in Figure 5.The five
classes are listed below in order of decreasing Vented
Unvented Enclosed
corrosion severity. Enclosed Exposure
Exposure Boldly
Partially sheltered exterior exposures. (Wall Cavity) Exterior Ex• sure
Examples include open, underhouse storage and MIN
parking areas below a piling-,column-,or post- o MI=
supported building and areas underneath roof
MEM
overhangs,decks, and walkways. Corrosion can - -
significantly weaken standard sheetmetal
Partially
connectors after 5 to 10 years in these exposures - a sheltered
on oceanfront buildings. Exterior
Exposure
Boldly exposed exterior exposures. Examples
include exterior walls with the connector fully
Figure 5. The locations of various classes of
exposed. If the exposed connector is fully dried L corrosion
5
between wettings by the ocean spray, the corrosion rate will be lower than that in partially
sheltered exterior exposures. Otherwise, the corrosion rate can match that in partially sheltered
exterior exposures.
Vented enclosed exposures,Attics, which must be vented to release excess heat and moisture,
are typical examples of this type of exposure. Corrosion will vary with the location of the
connector in the enclosed space. Corrosion rates for connectors near exterior vents, where
outside airflow is concentrated, are often similar to those for connectors in partially sheltered
exterior exposures. For connectors that are away from the vents or covered by insulation, the
corrosion rate is expected to be much lower.
Unvented enclosed exposures, Examples include enclosed floor systems with solid joists or
trusses. Because of the limited airflow and incoming salt spray,corrosion rates for connectors in
these exposures are expected to be lower than those for connectors in the previous three
exposures.
Interior living space exposures.These spaces are sealed from most salt spray, and normal
heating and cooling further reduce interior humidity below the threshold needed for rapid
corrosion. Connectors in these spaces should have the lowest corrosion rates.
Corrosion-Resistant Materials and Coatings
improved corrosion resistance can be obtained by fabricating connectors from more resistant
sheetmetal or by treating standard connectors after they have been fabricated. The relative
improvement in corrosion resistance for different options is estimated in this section. Better
materials can sometimes mean higher cost.Typical cost differences for the alternative materials
are also estimated in this section.
Thicker Galvanizing
There are two methods of producing thicker galvanizing on connectors: 1) fabricating connectors
from steel sheet with thicker initial galvanizing,or 2) regalvanizing standard connectors after
fabrication. Galvanized sheet steel is available in a variety of coating thicknesses. Several
manufacturers now market standard connectors in various designs fabricated from G 180 or G
200 grades of galvanized steel, which,compared to the standard G 60 connector, have zinc
coatings that are 3 or 3.3 times thicker, respectively. Since the corrosion resistance of zinc is
proportional to the thickness of the zinc, these connectors should last approximately 3 or 3.3
times longer, respectively, than standard connectors.Advertised costs for connectors with thicker
galvanizing have been known to range from 1.3 to 1.7 times the cost of standard connectors.
Thicker galvanizing can also be obtained by hot-dipping standard connectors after fabrication.
The manufacturer usually sends the connectors to an outside galvanizing company for dipping.
Several variables can affect the thickness of the galvanizing, but the result is typically a coating
of zinc four times thicker than that on a standard G 60 connector. A few types of these connectors
are regularly available. Other connector designs are available by special order. The cost estimate
for sheetmetal connectors hot-dipped after fabrication has been known to be roughly 1.75 times
the cost of standard G 60 grade connectors.
6
Stainless Steel
Several connector manufacturers also produce a variety of the most commonly used connectors
in stainless steel. Stainless steel is very resistant to corrosion in salt air and should last longer in
a wood-frame building than most other materials, even in the most corrosive oceanfront
situation. For extended lifetimes,stainless connectors must be attached with stainless steel nails
when separate fasteners are needed. Stainless steel sheetmetal is a more costly raw material than
the sheetmetal used to make galvanized connectors. It is also harder; therefore, stainless steel
connectors are more difficult to fabricate.The cost of a stainless steel connector, including the
cost of the necessary stainless steel nails,can be 6 to 15 times the cost of the same connector in
G 60 grade galvanized steel.
Paint Coatings
Painting standard galvanized steel connectors can significantly improve their corrosion
resistance. However many paints commonly used for buildings do not adhere well to galvanized
surfaces. The Truss Plate Institute (TPI) has considered the use of truss plates in corrosive
environments like coastal buildings.The TPI design specifications, which are accepted by the
national model codes, recommend that one of three types of industrial paint systems be applied
by brush to embedded plates after delivery of the completed truss to the job site or after truss
installation (see TPI-85).The paints are specific formulations of(1)epoxy-polyamide, (2)coal-
tar epoxy-polyamide, and (3) zinc chromate-vinyl butyral primer with asphaltic mastic.
The increased corrosion resistance provided by the recommended paint coatings in coastal
buildings is difficult to estimate. Unlike changes in galvanizing thickness,changes in paint
thickness do not proportionally change the corrosion resistance. Paint lifetimes are significantly
affected by salt spray,but exposure conditions can affect paints and galvanizing differently.
Surface preparation and care in application are critical for improved corrosion resistance with
paints. The added cost of these coatings will vary with local labor costs. In general,other types
of paints should not be assumed to significantly improve the corrosion resistance of standard
connectors or truss plates. For other types of connectors, the alternatives described previously
are recommended over any type of painting. However, for maintenance, zinc-rich coatings of
paint may be better than nothing.
Guidance for Connector Corrosion Control
All construction materials deteriorate with time.The average useful lifetime of the structural
components of a wood-frame building is approximately 70 years in the United States. Continued
use of a building requires that(a)the original materials be durable enough to last the expected
lifetime, (b)periodic maintenance be conducted to extend the life of original materials, or(c) the
material be replaced one or more times during the lifetime of the building.
Avoid the problem
Most connectors are intended for inland uses with mild corrosion and, under normal conditions,
appear to last as long as or longer than other materials in the building. Many buildings in
communities near the coast are likely to experience only slightly increased corrosion rates, and
standard connectors appear appropriate for those buildings. But close to the ocean, drastically
1► higher corrosion rates can be expected. The use of standard connectors in these areas may
7
necessitate care in controlling the exposure.
Otherwise, alternative materials should be used. Double-Band
Joist
Y1
For some uses,corrosion can be partially
avoided by altering the exposure of the •
connectors. For example,on exteriors, a
connector should be fully covered if possible or
otherwise protected from salt spray and
Floor
moisture. Exterior siding should be designed to A Joist
completely cover connectors.Applying siding
in this way changes the exposure from boldly Eger
exposed to unvented enclosed.An easy, but eon Nails Through
Ledger Board into
more costly, way to protect joist hangers and Double-Band Joist
truss plates in the floors of piling-supported
buildings is to sheath the underside of the floor Figure 6. Traditional wooden ledger boards used in
joists to reduce the exposure to salt air. Adding place of joist hangers in high-corrosion areas
such sheathing transforms one of the worst
exposures, partially sheltered exterior, into a
Nails Through less corrosive, unvented enclosed.
Floor
Beams into
Wind Anchor Joist For some connections,corrosion may be
avoided by not using sheetmetal. Underneath
111111 unsheathed floors and decks, the traditional use
,5 of ledger boards avoids the need for joist
I' � hangers in the worst corrosion exposures(see '
,,� Floor Beams Figure 6).The wooden wind anchors in Figure
IFFr, i
wood .'/I__:_ � 7 attach piling-supported floor beams to floor
e
joists.Commonlyused Anchors oI ed on the Texas coast,
Butts Through , these anchors proved effective during
Beams and Pile b Hurricane Alicia's 90-to 100-mph winds in
Square Wood Pile 1983.
Figure 7 Wooden wind anchors used to connect floor Maintenance and Replacement
joists to floor beams In some uses,connectors may be placed
whcrc they are accessible and maintainable. In milder exposures, applying a regular coat of
exterior house paint may be enough to extend the life of the connector. But in severe exposures,
even annual painting is unlikely to prolong the life of a connector to that of the rest of the
building. In these exposures, accessible connectors may be inspected for corrosion and, if
necessary. replaced. Galvanized sheetmetal connectors should be replaced as soon as partial
surface rusting appears. The presence of more than thin rusty edges indicates that the zinc
coating has been consumed and the sacrificial effects have been lost. Corrosion of the thin, steel
sheet will occur quickly and will rapidly deteriorate the structural integrity of the connector.
When the option of periodic replacement is evaluated,the cost over the lifetime of the building
should be considered. Corrosion-resistant connectors, available for a moderately higher price,
can have significantly longer lifetimes than standard connectors.The cost of labor for initial
installation is the same for both materials.The material and labor cost for even one replacement Nie
8
is often greater than the added initial cost for corrosion-resistant materials. By using better
materials initially, one can avoid the cost of two or three replacements of standard materials. In
the worst exposures, where standard connectors may have to be replaced as often as every 5
years,even the use of stainless steel connectors may prove less costly over the long run.
Given the low likelihood of regular inspection by most building owners and the brief expected
lifetime of standard connectors in the worst exposures, replacement is usually a poor option.
Furthermore, many connectors are hidden structural components that are difficult or impossible
to maintain or replace. In such cases, replacement is rarely an option and more corrosion-
resistant materials should be selected. Replacement may be the only option in existing buildings
where connectors have already been damaged by corrosion or were never installed. In existing
buildings, adding roof connectors can significantly improve the wind resistance and is therefore
worthwhile,even if some dismantling is needed to gain access.
Summary of Recommendations
For many connector applications in corrosion-prone buildings, the use of corrosion-resistant
materials is the best solution for new construction.The choice of alternative connector material
or coating specifications should be guided by the location of the building relative to the observed
corrosion hazards in each community and by the class of exposure in the building.
Recommended materials for a typical community are listed in Table 1.
Table 1 Recommendations for Corrosion—Resistant Materials and Methods"
Location Oceanfront Buildings Intermediate Rows of Buildings in Buildings Farther
Corrosion-Prone Areas Landward
Class of (300 feet or less from the shoreline)*** (300 to 3,000 feet from the (Greater than
Exposure °" shoreline 3,000 feet from
the shoreline)***
Partially I Avoid shcetmetal connectors where possible Use connectors with thicker Use connectors with
sheltered 22 Usc stainless steel connectors galvanizing. standard galvanizing,
3 Use connectors with thicker galvanizing and (Optional stainless steel) (Optional.thicker
exteriors replace them when necessary- galvanizing)
Boldly I Avoid sheetmetal connectorswhere possible. Use connectors with thicker galvanizing. Use connectors with
2 Use stainless noel connectors. (Optional stainless steel) standard galvanizing.
exposed
Use connectors with thicker galvanizing and (Optional.thicker
exteriors replace them when necessary galvanizing)
g
Vented I Usc connectors with thicker galvanizing I Use connectors with thicker galvanizing Use connectors with
enclosures (Optional stainless steel) near vents. standard galvanizing.
Use TPI paints on truss plates 2 Use TM paints on truss plates near vents. (Optional'thicker
i Optional for truss places thicker galvanizing.TPI (Optional thicker galvanizing for all galvanizing)
paints over thicker galvanizing.or stainless steel) connectors)
Unvented I Use connectors with thicker galvanizing. Use connectors with standard galvanizing. •Use connectors with
enclosures 2 Use TPI paints on truss plates. (Optional.thicker galvanizing) standard galvanizing
(Optional for truss plates-thicker galvanizing) (Optional•thicker
galvanizing)
Interior Use connectors with standard galvanizing. Use connectors with standard galvanizing. Use connectors with
living space (Optional:thicker galvanizing (Optional thicker galvanizing standard galvanizing
(Optional:thicker
galvanizing)
• Recommendartoaz are based cut the available research and are subject to change to future Technical Bulletins
•• See Figure S for corrosion classes.
••• Distances may vary c nnssderably depending on local climate The width of the corrosion hazard area misuse to the ocean should be determined in each
community from held observations and any eaistmg corrosion studies
9
In Table 1, building locations are categorized as oceanfront buildings, intermediate rows of
buildings in corrosion-prone areas, and buildings near the coast but far enough away from the
ocean that excessive corrosion is not anticipated. In most communities,connectors on
oceanfront buildings can be expected to corrode at high rates. Corrosion rates should approach
inland levels 300 to 3000 feet (roughly 100 to 1000 meters) landward of the ocean in most
communities.The types of connector exposures in a building are listed in Table 1 in order of
decreasing severity of location.Truss plate treatments are noted separately, based on TPI
recommendations for corrosive environments. Recommendations in the table are in some cases
based on limited research.When the severity of the exposure is unknown, selecting more
corrosion-resistant materials prudent. Optional materials for superior corrosion resistance are
also noted.
Technical Bulletins
This publication is one of a series of Technical Bulletins FEMA has produced to provide
guidance concerning the building performance standards of the NFIP.These standards are
contained in Title 44 of the U.S. Code of Federal Regulations at Section 60.3.The bulletins are
intended for use primarily by State and local officials responsible for interpreting and enforcing
NFIP regulations and by members of the development community, such as design professionals
and builders. New bulletins, as well as updates of existing bulletins,are issued periodically,as
necessary.The bulletins do not create regulations; rather they provide specific guidance for
complying with the minimum requirements of existing NFIP regulations. Users of the Technical
Bulletins who need additional guidance concerning NFIP regulatory requirements should
contact the Mitigation Division of the appropriate FEMA regional office.The User's Guide to
Technical Bulletins (FIA-TB-0) lists the bulletins issued to date and provides a key word/subject
index for the entire series.
Ordering Information
Copies of the Technical Bulletins can be obtained from the appropriate FEMA regional office.
Technical Bulletins can also be ordered from the FEMA publications warehouse. Use of FEMA
Form 60-8 will result in a more timely delivery from the warehouse. The form can be obtained
from FEMA regional offices and your state's Office of Emergency Management. Send
publication requests to FEMA Publications, P.O. Box 2012, Jessup, MD 20794-2012.
Further Information
1. Atmospheric Corrosion,edited by W. H.Ailor,John Wiley & Sons, 1982.
2. "Coastal Construction Manual,"FEMA, 1986, FEMA-55.
3 Corrosion Engineering, by M. G. Fontana& N. D. Greene, McGraw-Hill, 1986.
4. Corrosion Prevention by Protective Coatings, by C. G. Munger, National Association of
Corrosion Engineers, 1984.
5. "Design Specification for Metal Plate Connected Wood Trusses,"American National
Standards Institute,ANSI/TPI 1-95, Commentary and Appendix, 1995.
6. Marine Corrosion; Causes and Prevention. by F. R. LaQue,John Wiley & Sons, 1975.
/0
7. "Selected Specifications for Hot Dip Galvanizing," by the American Society for Testing and
Materials (ASTM), 1994, available from the American Galvanizers Association.
8. "Standard Specification for General Requirements for Steel Sheet. Zinc-Coated (Galvanized)
by the Hot-Dip Process,"ASTM, 1987,ASTM A 525-90.
Glossary
Base Flood—The flood that has a 1-percent probability of being equaled or exceeded in any
given year(also referred to as the 100-year flood).
Base Flood Elevation (BFE)—The height of the base flood, usually in feet, in relation to the
National Geodetic Vertical Datum of 1929 or other datum as specified.
Coastal-High Hazard Area—An area of special flood hazard extending from offshore to the
inland limit of a primary frontal dune along an open coast and any other area subject to high-
velocity wave action from storms or seismic sources. These areas are identified as V zones.
Federal Emergency Management Agency(FEMA)—The independent Federal agency that, in
addition to carrying out other activities,oversees the administration of the National Flood
Insurance Program.
Federal Insurance Administration (FIA)—The component of FEMA directly responsible for
administering the flood insurance aspects of the National Flood Insurance Program.
Flood Insurance Rate Map (FIRM)—The insurance and floodplain management map issued
by FEMA that identifies, on the basis of detailed or approximate analyses. areas of 100-year
4 flood hazard in a community.
Floodprone Area—Any land area susceptible to being inundated by floodwater from any
source.
Lowest Floor—The lowest floor of the lowest enclosed area of a structure, including a
basement.An unfinished or flood-resistant enclosure useable solely for parking of vehicles,
building access, or storage in an area other than a basement area is not considered a building's
lowest floor, as long as the enclosure is not built in such a way that it violates the non-elevation
design requirements of Section 60.3 of the National Flood Insurance Program regulations.
Mitigation Directorate—The component of FEMA directly responsible for administering the
floodplain management aspects of the National Flood Insurance Program and for carrying out
hazard mitigation activities related to flood and other disasters.
New Construction/Structure—For floodplain management purposes, new construction means
structures for which the start of construction commences on or after the effective date of a
floodplain management regulation adopted by a community and includes subsequent
improvements to the structure. These structures are often referred to as"Post-FIRM" structures.
Special Flood Hazard Area(SFHA) —Area delineated on a Flood Insurance Rate Map as
being subject to inundation by the base flood and designated Zone A,AE,A l-A30.AR.AO.AH,
V, VE,or V l-V 30.
11
Substantial Damage —Damage of any origin sustained by a structure whereby the cost of
restoring the structure to its before-damaged condition would equal or exceed 50 percent of the
market value of the structure before the damage occurred. .�
Substantial Improvement—Any reconstruction,rehabilitation, addition, or other improvement
of a structure, the cost of which equals or exceeds 50 percent of the market value of the structure
before the "start of construction"of the improvement. This term includes structures that have
incurred "substantial damage," regardless of the actual repair work performed.
12
t ru.t commuter er rwr1wc°matt iI! .m- awr